Bettinardi Queen B 14 Putter

Mallet Putter

Bettinardi's Queen B 14 is a mallet built for players who want the stability of a bigger head without giving up the soft, milled feel the brand is known for. Every Queen B putter gets cut from a single block of carbon steel at Bettinardi's shop in Tinley Park, Illinois, and the QB14 is no exception. You feel that pedigree the moment the face meets the ball. It's soft, but there's a crispness to it that cheaper cast putters can't fake.

The 14 in the name points to where it sits in the mallet family. This is a fuller-bodied shape than the blade-style Queen B models, with more mass pushed out toward the perimeter for a higher moment of inertia. That translates to a head that stays on line when you catch a putt slightly off-center, which happens more than any of us want to admit. The mid toe hang tells you who it's really for: a golfer with a moderate arc in their stroke, not a straight-back-straight-through robot.

Bettinardi aims the Queen B line at players who care about craft. If you've ever picked up a mass-produced mallet and felt like you were tapping a hockey puck, the QB14 is the antidote. It costs more, and it should. You're paying for milling precision and a feel that holds up round after round.

Design

The head is fully milled carbon steel, which gives the Queen B 14 its dense, muted feel at impact and a look that darkens and patinas over time if you skip the headcover. Bettinardi typically finishes these in a smoked or dark PVD coating to cut glare at address, and the milling marks on the face and flange are done in-house rather than stamped in. The alignment aid runs across the top of the mallet to frame the ball and give your eye a clear reference for squaring the face. Mid toe hang is the design choice that defines how this putter plays. The face rotates a moderate amount through the stroke, which pairs naturally with an arcing path. Weighting is distributed toward the heel and toe of the mallet body to raise forgiveness on mishits, so a putt struck near the edge of the face loses less speed and stays closer to your intended line than it would on a blade.

Who It's For

• You have a slight to moderate arc in your putting stroke and want a mallet that matches it instead of fighting it.
• Feel matters to you, and you'll pay a premium for milled carbon steel over a cast or insert putter.
• You miss the center of the face often enough that the extra forgiveness of a mallet head actually helps your scores.
• You want an alignment aid to help you set up square without a cluttered, busy top line.
• You appreciate that these are milled in the USA in small batches and you plan to keep the putter for years.

Technology

About Bettinardi

Bettinardi is one of the few brands that still mills every putter in their own facility. Their signature honeycomb face milling and one-piece construction create exceptional feel and consistency.

Specifications

Frequently Asked Questions

Is the Queen B 14 good for a straight-back-straight-through stroke?

Not the best match. The mid toe hang means the face wants to rotate through impact, which suits an arcing stroke. If your path is dead straight, look for a face-balanced mallet instead. You'll fight this one to keep it square.

What is the Queen B 14 made of and where is it milled?

It's milled from a single block of carbon steel at Bettinardi's facility in Tinley Park, Illinois. Carbon steel is what gives it the soft, dense feel. The trade-off is that carbon steel can develop rust or a patina if you don't keep it covered and dry, though the finish helps protect it.

How is the Queen B 14 different from Bettinardi's blade putters?

The QB14 is a mallet, so it has a larger head with more perimeter weighting and a higher MOI. That makes it steadier on off-center hits than a slim blade. A blade offers more feedback and a cleaner look for players who trust their stroke and want to feel every miss.

Does the alignment aid actually help?

If you struggle to aim, yes. The sight line across the top gives your eye a reference to square the face and frame the ball at address. Golfers who already aim well may find they don't need it, but it doesn't get in the way.

Is the Queen B 14 worth the price over a mass-produced mallet?

It depends on how much feel is worth to you. You're paying for full CNC milling and carbon steel, not a cast head with a foam insert. The feel and the build quality are a real step up. If you putt a lot and keep clubs for years, it earns its cost. If you want maximum forgiveness for the lowest price, cheaper mallets exist.

More from Bettinardi