CA
The Mack Daddy 3 Milled is Roger Cleveland's wedge, and it plays like a wedge built by someone who has spent decades obsessing over how a ball comes off a face. Callaway offers it across seven lofts from 48 to 60 degrees, so you can build a full short-game setup around one model without mixing feels between your gap, sand, and lob wedges.
What sets the MD3 apart is Groove-in-Groove technology. Between the main grooves, Callaway milled a second set of micro-grooves running at a slight angle to the primary ones. The point is more contact points on the ball at impact, which means more spin, especially on those half and three-quarter shots where you are trying to check a ball up next to a tucked pin. It is not marketing fluff. You can hear and feel the ball grabbing the face.
Progressive lofts and progressive grooves mean this set is not one design stretched across seven heads. Lower lofts get narrower, deeper grooves for full-swing control. Higher lofts get wider, shallower grooves tuned for spin around the greens. If you play a 48 and a 60 out of this family, each one is optimized for the shots you actually hit with it.
简而言之
The Callaway MD3 Milled (2015) is a tour-grind wedge built for shotmaking and versatility around the green. Lofts run 48° to 60°.
Callaway MD3 Milled 挖起杆: 关键参数
- 类别
- Tour Grind
- 杆面倾角范围
- 48 to 60 degrees
- Loft/grind options
- 7
- 型号年份
- 2015
现在买还是再等等？
买或等Refresh due soon
Brands in this category update about every 2 years, and the MD3 Milled is 11 years old with no successor yet, so a new model could land any time. Grab it at clearance pricing now, or wait a few weeks to see what replaces it.
Based on release timing and this line's typical refresh cycle, not a live price quote.
可选版本
| 杆面倾角 | 弹跳角 | 研磨 | Finish |
|---|---|---|---|
| 48° | 10° | S | Chrome |
| 50° | 10° | S | Chrome |
| 52° | 10° | S | Chrome |
| 54° | 10° | S | Chrome |
| 56° | 10° | S | Chrome |
| 58° | 10° | S | Chrome |
| 60° | 10° | S | Chrome |
Loft and bounce are nominal values. Actual specifications may vary.
技术
About the Callaway MD3 Milled
The MD3 Milled is forged and then CNC milled on the face and grooves, which is why the shorthand name includes Milled. Milling the face gives Callaway tight tolerances groove to groove, and the forged carbon steel head delivers the soft, dense feel that better players want to hear on a delicate flop or a firm spinner. This is a players wedge in look and feel, with a compact head, thin topline, and minimal offset. Grind options were the other half of the story. Depending on loft you could get an S grind for versatility, a C grind with heel and toe relief for players who open the face and manipulate the club, or a W grind with more bounce for softer conditions and steeper attack angles. Matching the grind to your turf and your swing is the difference between a wedge that digs and one that glides.
Who Should Play the Callaway MD3 Milled?
- ✓Mid to low handicappers who take a full or partial swing and want the ball to check on the second bounce.
- ✓Players who want a matched set of wedges from gap through lob rather than a single hero club.
- ✓Anyone who opens the face and works shots around the green and needs a grind that lets the club slide instead of dig.
- ✓Golfers who prioritize spin and feel from forged carbon steel over the durability of a plated cast wedge.
常见问题
What is Groove-in-Groove technology on the MD3 Milled?
It is a second set of micro-grooves milled between the main grooves, angled slightly against them. The extra edges create more contact with the ball at impact, which adds spin on partial and open-face shots where you need the ball to stop quickly.
What grind should I get in the Callaway MD3 Milled?
It depends on your turf and technique. The S grind is the versatile all-rounder for neutral conditions. The C grind has heel and toe relief and suits players who open the face and hit a lot of finesse shots. The W grind carries more bounce and works better in soft turf and bunkers or if you have a steep angle of attack.
Is the MD3 Milled forged or cast?
It is forged from carbon steel with a milled face and grooves. The forging gives it the soft feel better players look for, and the milling keeps the grooves consistent for predictable spin.
Which lofts does the MD3 Milled come in and how should I set up my wedges?
It runs from 48 to 60 degrees in the 48, 50, 52, 54, 56, 58, and 60 options. Most players carry three or four wedges spaced about four degrees apart, for example a 50, 54, and 58, so you cover your gaps without leaving an awkward yardage between clubs.
Is the MD3 Milled a good wedge for higher handicappers?
It can be, but it is built for players who make consistent contact. This is a compact players wedge with a thin topline and less bounce in the lower-loft grinds. If you tend to hit it thin or fat, a wider-soled game-improvement wedge will be more forgiving, though you give up some of the feel and spin the MD3 delivers.
评分与评价
No ratings yet. Sign in to rate this club.
Alternatives to the Callaway MD3 Milled
Other tour grind wedge models from different brands, closest to its model year.
More Callaway 挖起杆
Find the right loft for your bag
Use the gap finder to see which loft combination fits your current set.
Open Gap Finder →